Epoxy Clear Food Safe Coating FDA Compliant 4 Vertical Application Less Sagging
Specifications
| Return Shipping Will Be Paid By | Buyer |
| All Returns Accepted | Returns Accepted |
| Item Must Be Returned Within | 30 Days |
| Refund Will Be Given As | Money Back |
| Model | MAXCLRTHIXO96 |
| Country/Region Of Manufacture | United States |
| Custom Bundle | Yes |
| Country Of Manufacture | United States |
| TWO COMPONENT EPOXY SYSTEM | Room Temperature Cure |
| MPN | MAXCLRTHIXO96 |
| Brand | MAX CLR THIXO |
PROPER CURINGTo achieve the best cure results, the ambient condition should be between 75°F to 85°F and the relative humidity is below 57%. The colder the temperature the longer takes to fully cure. Use an infrared lamp to warm the ambient temperature. Infrared lamps also work well for warming large work areas. Post Curing at 150°F for 2 hours will accelerate full curing. Use radiant heat from an IR lamp or a processing oven if available.Rinse the surface with warm water and mild detergent before use. DEGLOSSINGOnce the MAX CLR THIXO fully cures, deglossing the surface to create a satin finish can be easily done using an abrasive pad.In this demonstration, a SCOTCHBRITE pad was used to de-gloss the surface.Note the dramatic decrease in gloss after a light polishing with the abrasive pad. Very-fine sandpaper (wet-sanding) also works well. PHYSICAL AND MECHANICAL PROPERTIESViscosityDensity Form and Color1,200 - 2000 cPs @ 25°C Mixed- Slightly Thixotropic 1.10 g/cc Transparent Clear Upon CureMix Ratio100 Parts Resin: 50 Parts Curing Agent By Weight or by Volume 2:1 (Part A to Part B)Working Time45 Minutes @ 25°C (100-gram mass)Peak Exotherm70°C (158°F, 100-gram mass)Handle Time Full Cure Time5.5 Hours 36 Hours minimum @ 25°C (75°F)Hardness72± 5 ShoreTee-Peel Strength5.7 Lbs per inch WidthTensile Shear Strength1,300 psi @ 25°C (77°F) 800 psi @ -80°C (-112°F) 550 psi @ 100°C (212°F)Elongation9.0% @ 25°C (77°F)Compressive Strength2,200 psi @ 25°C (77°F)Heat Distortion Temp80°C (176°F)CHEMICAL RESISTANCE PERFORMANCE FULL IMMERSION at 75°F MEASURED PERCENT CHANGE IN WEIGHT Specimen Cure - 7 days @ 25ºC plus 1 hours at 220°F Specimen Size - 1 Cubic Inch Percent Change In Weight REAGENT 3 days 28 days Deionized Water 0.29% 0.30% Sea Water 0.11% 0.38% 100% Methanol 7.93% Destroyed -2.41% Destroyed 80% Ethanol 3.98% 4.28% Toluene 0.40% 2.86% Xylene 0.14% 0.25% Butyl Cellosolve 6.63% 5.31% MEK 2.7% Destroyed 10% Lactic Acid 0.11% 0.42% 10% Acetic Acid 0.11% 0.45% 70% Sulfuric Acid 0.08% 0.14% 50% Sodium Hydroxide 0.1% 0.1% 30% Sodium Hypochlorite 0.51% 1.36% HOT WATER IMMERSION TEST WOOD COATED MUGMAX CLR A/B HOT WATER IMMERSION TESTVideo will open in a new window Please Check Out Other Available Resin Systems At Our eBay StoreFor our complete listing, please Visit our eBay store!DON'T FORGET OUR EPOXY MIXING KITEverything You Need To Measure, Mix, Dispense & Apply The Epoxy ResinClick The Link To Add To Orderhttps://www.ebay.com/itm/222623932456 Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system. The container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system. The container must withstand the tenacity of the chemical and must be free of contamination. Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature.MIXING KIT CONTENTS 1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams 4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix CupsOne Size Fits All Powder-Free Latex Gloves 2 Each Graduated SyringesWooden Stir SticksAssorted Size Foam Brush IMPORTANT NOTICEYour purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product. The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval.The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.